A Valvetronic problem on an N55 engine can be troublesome: variable valve lift errors appear, the car loses power or goes into limp mode. Sometimes the engine control unit is damaged as well. That raises the question: should you clone the control unit, and how do you do it so that the fault does not come back?
The workstation where we work on an engine control unit: a Multi-PROG programmer, a microscope, a lamp and a laptop.
This text describes our approach to such a situation. It does not give details of any particular car, because the photo shows the workstation, not the cause of a fault.
Symptoms where it is worth starting with diagnostics
A valve lift system error, uneven engine running, loss of power, limp mode or no communication with the control unit are signals that must not be interpreted hastily. They can have several different causes, and only some of them concern the control unit itself. Before anyone starts replacing or cloning electronics, you have to check what has really failed.
What the Valvetronic system is
Valvetronic is a system for continuously variable control of intake valve lift. It includes, among other things, an electric motor, a position sensor and a wiring harness with connections. A failure of any of these components can produce errors and symptoms similar to a faulty control unit, and in some situations accompany its failure. This cannot be settled without diagnostics, so we do not guess.
Cause first, then cloning
This is the most important rule. If the control unit was damaged by a problem in the Valvetronic system (for example the motor, a sensor or the wiring harness), and you fit a working, cloned control unit without eliminating the cause, the fault may come back and the control unit may be damaged again.
So the order is as follows:
- Diagnostics: reading fault codes, checking the system, assessing the components (motor, sensors, wiring harness).
- Eliminating the cause of the fault that has been identified.
- Only then cloning the control unit, that is, transferring the data to a working unit.
Cloning does not repair the Valvetronic system. It transfers the data to a working control unit, and the actuators and the wiring harness have to be checked separately.
How control unit cloning works
On our workstation (a Multi-PROG programmer, a microscope and a laptop) we proceed as follows:
- we assess the donor control unit and the faulty one for compatibility,
- we read the data and prepare it for writing,
- we write the data to the working unit, working with protection against electrostatic discharge,
- we check the write and send the control unit back, ready to install.
This is repair by replacing the faulty control unit with a working one, not a change to how the engine behaves. You will find the description and scope of the service on the page cloning and repair of BMW control units.
When the control unit alone may be at fault
Sometimes the trouble lies solely in the control unit: a damaged circuit on the board, the result of a surge, flooding or a power supply fault. In that case, once it has been checked that the Valvetronic system is sound, cloning makes sense. If you are not sure, start with diagnostics. We describe similar reasoning for the MSV70 and MSD81 control units, and you will find a comparison with repairing or buying a control unit in the article when ECU cloning makes sense.
If the car also has other engine running symptoms, full diagnostics in a workshop can help, for example BMW N53 diagnostics for N53 engines or N43 diagnostics.
How to prepare your enquiry
Before you contact us, note which errors the car shows, when the first failure occurred and whether anyone has worked on the system before (replacing the Valvetronic motor or a sensor, work on the wiring harness). Take a photo of the control unit label with the part number. This information helps us assess more quickly whether cloning is needed at all or whether the system itself must be dealt with first.
Sending the control unit
You can send the control unit by courier from anywhere in Poland. We agree the scope and price before shipping, carry out the work and send the module back. If you also have a faulty FRM module, we have a separate service: FRM3 module repair by post.
Frequently asked questions
Not always. System errors can come from the motor, a sensor or the wiring harness. The control unit may be damaged independently or together with them, which is why diagnostics is needed.
Better not before the cause has been established. If the fault remains, it may come back and damage a working, new control unit as well.
No. Cloning transfers the data to a working control unit, but it does not repair the engine, the sensors or the system's wiring harness.
Yes, cloning can be carried out after you send the control unit by courier. We agree the details after you describe the car and the symptoms.
Valvetronic problem on an N55?
Describe the symptoms and the condition of the control unit, and we will help establish whether diagnostics or cloning is needed first.
Ask about cloning