Language: PL EN DE FR
Case study · ECU cloning

MSV70 ECU cloning: transferring the data to a working unit

Silesia Codemasters · Case studies · ~3 min read

The MSV70 is an engine control unit (DME) used in many BMWs with naturally aspirated six-cylinder N52 engines. When one fails, you are usually told you have to buy a new one from the dealer. Often there is another way: transferring the contents of the faulty unit to a working one. That is what MSV70 ECU cloning is, and in this article we describe how we approach the service.

ECU workstation: a laptop with software, a Multi-PROG programmer, a control unit with leads on an antistatic mat and workshop tools

The cloning workstation: a laptop, a Multi-PROG programmer and a control unit connected by leads on a workbench.

We write about what the service is and how we run it. The photo alongside shows our workstation while working on a control unit of this type. We do not give details of any particular car or customer.

What engine ECU cloning is

Cloning is not "tuning" and it does not change how the car behaves. It is repair by replacement: we transfer the data from the faulty control unit (the software and settings assigned to that particular car) to a working unit that is to be its successor. After installation the engine runs on the same data as before, and you do not have to go through a long reconfiguration.

You will find the full description of the service, including the postal option, on the page cloning and repair of BMW control units.

When MSV70 cloning makes sense

Most often when:

Cloning replaces the faulty control unit, but it does not remove the cause of its failure. If a surge was caused by a short circuit in the wiring harness or on an actuator, the new control unit may fail for the same reason.

How cloning works, step by step

Below is the general course of a job. The details depend on the control unit version and the condition it arrives in.

  1. You report the control unit: you give the car model and the part number from the label and describe the symptoms. We make an initial assessment of whether cloning is the right way forward.
  2. We check the donor control unit (the working one) and the faulty control unit for compatibility.
  3. On a workstation with a programmer we read the data, prepare it and write it to the working control unit. We work with protection against electrostatic discharge.
  4. We check that the write is correct and send the control unit back, ready to install.

The photo shows the typical equipment of such a workstation: a laptop, a Multi-PROG programmer, a control unit connected by leads and a container marked ESD.

What cloning does not solve

Cloning transfers data; it does not repair the rest of the system. It will not solve problems with injectors, coils, sensors, the power supply or a damaged wiring harness. That is why it is worth establishing the cause before you decide, for example through BMW N53 diagnostics or N43 diagnostics, when the engine is not running properly for another reason. Only then does it make sense to transfer the data.

We described the general comparison of the approaches (repair, cloning, a new or used control unit) in the article BMW ECU cloning: when it makes sense. A related subject is the MSD81 control unit, covered in a separate text: MSD81 ECU cloning.

How to prepare your enquiry

Take a photo of the control unit label with the part number, note the car's model, year and engine, and describe what happened before the failure. If you already have a used control unit, give us its number and we will check compatibility before you send it.

Sending the control unit

You do not have to come in. Usually it is enough to send just the control unit by courier (and the working unit, if you have one); we carry out the agreed work and send it back ready to install. We agree the scope and price before shipping, after you describe the situation. We run FRM3 module repair by post in a similar way.

Frequently asked questions

It was used in many BMWs with naturally aspirated six-cylinder N52 engines, but the range of models depends on the model year. The part number on the control unit label lets us check whether a particular unit qualifies.

Cloning needs a working unit with a compatible version, onto which we transfer the data. You can buy a used control unit yourself, or ask us what will fit.

The aim of cloning is for the control unit to run on its predecessor's data, with no reconfiguration. We confirm any additional work when we quote, because it depends on the condition of the control unit.

No. Cloning transfers the data to a new unit, but it does not remove the cause of the failure. The actuators and the wiring harness must be checked separately.

Yes, the service is available by post from all over Poland. Describe the car and the symptoms and we will agree the scope before you send it.

Faulty MSV70 control unit?

Describe the car model, the part number and the symptoms, and we will tell you whether cloning makes sense and how to organise it.

Ask about cloning

See also

New: SC Diag — BMW engine diagnostics on your phone and laptopAn Android app and a Windows program: reading BMW and MINI engine control units (97 control units, petrol and diesel). The log analysis and report are prepared by Silesia Codemasters.See the app →
f