Ruda Śląska is where we are based – the only city where you can either visit us in person or ask us to come to your address. BMW computer diagnostics, coding, programming and chip tuning with professional diagnostic equipment, without rushing, because we are on our own ground.
Silesia Codemasters operates from Ruda Śląska – this is where we have the full workshop, the complete set of professional diagnostic software and every tool needed for coding and programming BMW control units. Customers in other cities wait for us to travel to them – if you are in Ruda Śląska, you have a choice: come to us or ask us to come to your address.
This makes a real difference for coding and programming – jobs that sometimes need a long, stable session on a constant power supply. In the workshop we have ideal conditions for that, without the compromises of a mobile visit.
We serve all districts – Ruda, Nowy Bytom, Bykowina, Chebzie, Halemba, Kochłowice, Orzegów, Wirek, Godula, Bielszowice and Kończyce. Once we are on site, getting around the city usually takes just a few to a dozen or so minutes, so flexibility here is greater than anywhere else we serve.
The only city within our area where you can choose either option.
Mon–Thu 14:00–19:00, Fri 14:00–20:00 – and at weekends from as early as 6:00: Sat 6:00–20:00, Sun 6:00–18:00, always by prior appointment.
Stable power supply, the complete software set, none of the compromises of a visit in the field.
Everything below is carried out on site at our base – and on request, also at your address anywhere within the city.
Full scan of all control units, live data readout and fault analysis with professional diagnostic equipment.
Over 100 supported makes – not only BMW, but also European, Asian and electric cars.
Personalisation and activation of factory functions, matched to the equipment and platform of your car.
Programming and matching of control units – including those replaced after a failure or imported second-hand.
Increase your BMW engine's power on the Autotuner, with DynoPRO dyno measurements before and after programming. See our full BMW chip tuning offer.
In person within 1 hour, or by post from anywhere in Poland from PLN 200 (return shipping is extra – InPost parcel locker PLN 15 – or PLN 250 including shipping), returned the same day. See the FRM3 module repair.
Installing newer control unit software versions in line with the vehicle specification.
Professional diagnostic software supporting the manufacturer's protocols — full reading of parameters, adaptations and fault memory.
Component adaptations after repair and permanent fault clearing once the cause has been confirmed and eliminated.
Repairs preceded by genuine diagnostics – from timing drives to suspension and the braking system.
A full check of the car before you sign the contract – fault history, adaptations, the real condition of the control units.
BMW coding is one of our most frequently ordered services in Ruda Śląska – from personalising comfort settings and activating manufacturer-intended functions to matching control units after replacement. The rule is always the same: reliable diagnosis or compatibility check first, configuration changes only afterwards.
The fault code is only the starting point – live data shows whether the problem is serious or merely cosmetic.
Knocking, vibration at idle or loss of power under acceleration – common symptoms on direct-injection engines.
A part was replaced but the symptom is back – a sign that the real cause should be verified by independent diagnostics.
A full control unit readout shows the real technical condition, regardless of what the advert says.
A new or used module has to be programmed and matched to your specific vehicle before it can work properly with the rest of the car.
Diagnostics before signing the contract is the cheapest insurance against an expensive surprise after the purchase.
If your BMW has an N53 or N43 engine – among the most frequently misdiagnosed units of the brand – also see our detailed pages on the typical symptoms of these engines: N53 diagnostics and N43 diagnostics. And if you are looking specifically for coding anywhere in Silesia, see our dedicated BMW coding page.
You write or call, choose – come to us or have us come to your address in Ruda Śląska – and describe what you need.
Full workshop facilities on site – stable power supply, the complete set of professional diagnostic software, no rush.
Results, parameters and recommendations in a document that stays with you for good.
Instead of replacing parts "by trial and error", we start with full diagnostics of live parameters. This approach shows in customer reviews – 60 Google reviews and an average rating of 5.0, most of them about accurate diagnosis before an expensive repair.
We work with professional diagnostic software supporting the manufacturer's protocols, so the range of services in Ruda Śląska covers full diagnostics, coding and programming, with a far more personal approach.
Besides BMW, we also run computer diagnostics on over 100 makes, so if there is another make parked in your garage next to the BMW, one visit can take care of both.
Diagnosis of a DPF problem, service, I-Level update and Stage 1 with dyno measurement: from 166 hp and 371 Nm to 205 hp and 443 Nm. Full description →
Replacement of a seized NOx sensor, registration of the new sensor, engine readaptation and an adaptation drive. Full description →
Full diagnostics, dynamic logs and chip tuning to the customer's specification, with measurements before and after. Full description →
Tow bar retrofit configuration, control unit programming and coding, plus full system diagnostics – done on site at the customer's address in Ruda Śląska. Full description →
It is the only city where you have both options – Ruda Śląska is our home base, so you can either come to us or ask us to come to your address, whichever is more convenient.
Yes – Ruda, Nowy Bytom, Bykowina, Chebzie, Halemba, Kochłowice, Orzegów, Wirek, Godula, Bielszowice and Kończyce. Once we are on site, getting around the city usually takes just a few to a dozen or so minutes.
No – most coding and feature activations take from a dozen or so minutes to an hour, depending on the scope. We do it on the spot, and your car does not stay with us longer than the job itself.
Yes. Being here on site, it is easy to arrange regular, recurring servicing of a fleet – both at our workshop and at your company's address.
Yes – we run computer diagnostics on over 100 makes. BMW remains our main specialisation for coding and programming.
Coding is changing the configuration of a control unit that is already installed – for example activating a function provided by the manufacturer. Programming is installing or updating the control unit software, for example after the unit has been replaced.
Yes – every visit ends with a PDF report with results, parameters and a description of the faults found, which stays with you for good.
Often yes, especially for shorter jobs such as coding. The quickest way to check availability is to write or call us directly.
Diagnostics, coding, programming, chip tuning and full mechanics – yes, this is our home base, so we have the full workshop facilities on site.
Configuration of the fitted tow bar, control unit programming and coding, carried out on site at the customer's address in Ruda Śląska.
See the job description →Diagnostics, DPF system service, software update and Stage 1 with DynoPRO dyno measurement.
See the job description →Diagnostics, dynamic logs and engine software modification to the customer's specification.
See the job description →Customers from near Warsaw travelled to Ruda Śląska. Sensor replacement, registration, engine readaptation.
See the job description →For us, Ruda Śląska is not just another stop along the route – it is the base from which we work across the whole region. Computer diagnostics, coding, control unit programming, BMW chip tuning, full mechanics and pre-purchase checks – all available in person, without the compromises of a mobile visit, or with travel to you if that is more convenient. Always the same approach: reliable diagnosis first, the decision about repair afterwards.
Write or call – we will agree whether it is more convenient to come to us or have us come to you.
Check available dates