VANOS is a variable valve timing system that BMW has used for years in most of its inline engines. When it starts to fail, the symptoms can be so ambiguous that they are easily confused with completely different faults – and that is a straight road to needlessly replacing parts that are not at fault.
What VANOS is for
The mechanism changes, in real time, the angle of the camshafts relative to the crankshaft, optimising engine operation according to rpm and load. This gives the engine better torque at low revs while keeping good performance at high revs – a similar aim to that described for the DISA valve, only achieved by a different method.
How it shows
- Rattling at start-up, especially noticeable on a cold engine, going away after a few seconds of running.
- Loss of torque in the mid-range.
- Rough running under varying load.
- The engine warning light with a fault code relating to camshaft timing correction.
Why it is so easily confused with another fault
Rough running and loss of torque are symptoms shared by many different faults – from ignition problems, through vacuum leaks, to worn components of the fuel system. Without checking the specific timing correction data, VANOS is either overlooked or, conversely, blamed unnecessarily when the real problem lies elsewhere.
If the rattling appears mainly on a cold engine and goes away after a moment, it is a typical pattern for early VANOS wear – usually linked to insufficient oil pressure in the mechanism just after start-up, before the oil pump reaches full output.
How we check it
In diagnostics we analyse the actual timing correction values in real time, comparing them with the values requested by the control unit under different engine operating conditions. This lets us confirm whether the problem really lies in the VANOS mechanism or in a completely different component producing similar symptoms.
The most common causes of VANOS faults
- Dirty solenoid valves. The solenoids that control oil flow have small screens and channels that clog with deposits. The valve then reacts with a delay or not at all.
- Oil and oil changes. VANOS works on engine oil pressure. Stretched service intervals and oil of the wrong viscosity are the shortest road to problems.
- Hardened seals. In older inline engines the VANOS piston seals harden with age and stop holding pressure. The mechanism then works weakly, usually without a hard fault code.
- Timing drive wear. A stretched chain and worn guides produce camshaft correlation errors that are easily mistaken for a fault of VANOS itself.
- Low oil pressure. If the pump or the regulating valve cannot maintain pressure, VANOS has nothing to work with. How to tell a real problem from a sensor fault is covered in our article on oil pressure.
VANOS across different BMW engine generations
The first versions of the system controlled only the intake camshaft. Later came double VANOS, which also covers the exhaust camshaft, known from engines such as the M52TU and M54. In newer N- and B-series units the mechanism is built differently: rotary adjusters on the camshafts controlled by two solenoid valves at the front of the head. That is why typical faults differ between generations. In older engines the seals are more often to blame, in newer ones the valves and oil quality.
What to check before replacing the whole mechanism
- The oil. Level, condition and date of the last change. Fresh oil of the correct specification can on its own improve VANOS operation.
- The solenoid valves. In many engines the intake and exhaust valves are identical. Swapping them over shows whether the fault "follows" the valve. If so, the valve is to blame, not the mechanism.
- Cleaning the valves. Often enough to restore correct operation.
- A diagnostic test. Comparing requested and actual angle on a warm engine at different rpm.
- Timing chain condition. Especially when the faults concern correlation of the camshafts with the crankshaft.
This order starts with the cheapest things. Replacing the adjusters is the last step, not the first.
Frequently asked questions
It is one of the more characteristic symptoms, especially when it appears mainly on a cold engine and goes away after a short while, but it is worth confirming with diagnostics – other timing components can make a similar sound.
In the short term yes, though with noticeably poorer running quality and a loss of torque in part of the rev range. Delaying the repair raises the risk that fine particles from worn components will contaminate the oil and affect other parts of the lubrication system.
It depends on the engine – in many BMW units it is fitted separately on the intake and exhaust camshaft, which means the fault may concern only one of them, giving a slightly different set of symptoms.
Not always – sometimes it is enough to replace the solenoid valve that controls the mechanism or to clean clogged oil passages. The scope of the repair is best set after diagnostics, rather than assuming the most expensive scenario from the start.
Hearing a rattle at start-up?
We will check the real timing correction values before you replace the whole VANOS mechanism.
Book engine diagnostics