BMW OBD2 fault code database — over 149 codes explained in English

BMW fault codes — find out what your code means.

Enter the code number from your OBD2 reader (e.g. P0301) or a keyword — find out what the fault involves, what symptoms it causes, and whether it's worth diagnosing on site right away.

5.0 · 60 Google reviews
Over 149 codes in the database
// How to use the database

A code is a starting point, not a final diagnosis.

A fault code from the car's computer shows the area of the problem — e.g. a specific cylinder, sensor or system — but rarely points straight to one specific damaged part. The database below will help you understand what your code is about before you decide what to do next. If you want to be sure of the actual cause, book a full diagnostic on professional equipment.

The database below covers standard OBD2 (SAE) codes — a universal diagnostic standard used across all makes, including BMW. Couldn't find your code? Get in touch — during diagnostics we check the full range of codes, including those specific to particular BMW models and control units.

// Code database

Search for your fault code.

Found: 0 codes

Engine sensors and air measurement

P0100

Air flow sensor circuit (MAF)

Fault in the mass air flow sensor (MAF) circuit — the control unit isn't receiving a correct signal.

Symptoms: Rough running, hesitation, power loss.

P0101

MAF — signal out of range

The MAF sensor reading doesn't match current engine operating conditions.

Symptoms: Power loss, rough idle, increased fuel consumption.

P0102

MAF — signal too low

Voltage from the MAF sensor is lower than expected.

Symptoms: Poor throttle response, engine bogging down.

P0103

MAF — signal too high

Voltage from the MAF sensor is higher than expected.

Symptoms: Overly rich mixture, black exhaust smoke.

P0106

MAP/pressure sensor — out of range

The signal from the intake manifold pressure sensor (MAP) deviates from the expected range.

Symptoms: Rough idle, power loss.

P0107

MAP — signal too low

Voltage from the MAP sensor is lower than it should be.

Symptoms: Overly rich mixture, engine hesitation.

P0108

MAP — signal too high

Voltage from the MAP sensor is higher than it should be.

Symptoms: Overly lean mixture, power loss.

P0110

Intake air temperature sensor circuit (IAT)

Fault in the intake air temperature sensor (IAT) circuit.

Symptoms: Incorrect fuel metering, hard cold starting.

P0113

IAT — signal too high

The control unit reads an unrealistically high intake air temperature.

Symptoms: Lean mixture on a cold engine.

P0115

Coolant temperature sensor circuit (ECT)

Fault in the engine coolant temperature sensor (ECT) circuit — critical for fuel metering and fan operation.

Symptoms: Incorrect temperature reading on the dash, starting problems.

P0117

ECT — signal too low

The control unit reads an unrealistically high coolant temperature.

Symptoms: Overly lean mixture, radiator fan behaving abnormally.

P0118

ECT — signal too high

The control unit reads an unrealistically low coolant temperature.

Symptoms: Overly rich mixture, extended warm-up mode.

P0128

Thermostat — engine takes too long to warm up

The engine doesn't reach operating temperature within the expected time — most often a thermostat stuck open.

Symptoms: Slow engine warm-up, increased fuel consumption, weak cabin heating.

P0120

Throttle position sensor circuit (TPS)

Fault in the throttle position sensor circuit.

Symptoms: Hesitation when pressing the accelerator, rough idle.

P0121

TPS — signal out of range

The throttle sensor signal doesn't match other engine operating parameters.

Symptoms: Unpredictable accelerator pedal response.

P0125

Insufficient coolant temperature for closed loop fuel control

The engine doesn't reach the temperature needed to switch fuel mixture control into closed-loop mode.

Symptoms: Increased fuel consumption, longer warm-up time.

P0016

Crankshaft/camshaft timing misalignment (Bank 1, Sensor A)

The crankshaft and camshaft position sensor signals are out of sync — often caused by a stretched or skipped timing chain.

Symptoms: Distinctive rattle on cold start, loss of power, sometimes the engine won't start.

P0017

Crankshaft/camshaft timing misalignment (Bank 1, Sensor B)

Same as P0016, but for the second camshaft sensor on bank 1 (exhaust side).

Symptoms: Timing chain rattle, rough running, power loss.

P0018

Crankshaft/camshaft timing misalignment (Bank 2, Sensor A)

Same as P0016, but for bank 2 (V-configuration engines).

Symptoms: Timing chain rattle, power loss.

P0019

Crankshaft/camshaft timing misalignment (Bank 2, Sensor B)

Same as P0017, but for bank 2.

Symptoms: Timing chain rattle, rough running.

P0089

Fuel pressure regulator performance

The high-pressure fuel system regulator isn't holding the target pressure — often caused by a worn high-pressure pump.

Symptoms: Hesitation, power loss, hard starting.

P0193

Fuel rail pressure sensor — signal too high

The fuel pressure sensor voltage is higher than expected.

Symptoms: Overly rich mixture, possible power loss.

P0190

Fuel rail pressure sensor circuit

Electrical fault in the fuel pressure sensor circuit — the control unit has no reliable pressure reading.

Symptoms: Hesitation, hard starting, irregular engine running.

P0219

Engine overspeed condition

The engine exceeded its maximum allowed RPM (overrev) — usually a one-off event, not a component fault.

Symptoms: Usually no lasting symptoms if the event was brief.

P0230

Fuel pump primary circuit

Electrical fault in the main fuel pump control circuit.

Symptoms: Hard starting, no fuel delivery, possible engine stalling.

P0234

Boost pressure overload (overboost)

The turbocharger/compressor produces higher boost pressure than allowed — common with chiptuning using a poorly matched map.

Symptoms: Limp mode, sudden power loss, sometimes exhaust smoke.

P0299

Insufficient boost pressure (underboost)

The turbocharger isn't producing the required boost pressure — common causes: a leaking intercooler, a faulty wastegate, or a leak in the intake system.

Symptoms: Noticeable power loss, a feeling of 'no turbo'.

Oxygen sensors and air-fuel mixture

P0130

Oxygen sensor circuit (Bank 1, sensor 1)

Fault in the front oxygen sensor circuit on bank 1.

Symptoms: Increased fuel consumption, rough running.

P0133

Oxygen sensor — slow response (Bank 1, sensor 1)

The oxygen sensor responds more slowly than it should to mixture changes.

Symptoms: Higher fuel consumption, rougher engine running.

P0135

Oxygen sensor heater circuit (Bank 1, sensor 1)

Fault in the front oxygen sensor's heater circuit.

Symptoms: Longer time to reach full mixture-control accuracy.

P0136

Oxygen sensor circuit (Bank 1, sensor 2)

Fault in the rear oxygen sensor circuit (after the catalytic converter) on bank 1.

Symptoms: Usually no noticeable symptoms — detected during emissions checks.

P0141

Oxygen sensor heater circuit (Bank 1, sensor 2)

Fault in the rear oxygen sensor's heater circuit on bank 1.

Symptoms: Usually no noticeable driving symptoms.

P0150

Oxygen sensor circuit (Bank 2, sensor 1)

Fault in the front oxygen sensor circuit on bank 2 (V6/V8/V12 engines).

Symptoms: Increased fuel consumption, rough running.

P0155

Oxygen sensor heater circuit (Bank 2, sensor 1)

Fault in the front oxygen sensor's heater circuit on bank 2.

Symptoms: Longer time to reach accurate mixture control.

P0171

System too lean (Bank 1)

The control unit detected too much air relative to fuel on bank 1 — a common cause is an intake system leak.

Symptoms: Hesitation at idle, power loss, sometimes a fuel smell.

P0172

System too rich (Bank 1)

The control unit detected too much fuel relative to air on bank 1.

Symptoms: Black exhaust smoke, increased fuel consumption, fuel smell.

P0174

System too lean (Bank 2)

The control unit detected too much air relative to fuel on bank 2.

Symptoms: Hesitation at idle, power loss.

P0175

System too rich (Bank 2)

The control unit detected too much fuel relative to air on bank 2.

Symptoms: Black exhaust smoke, increased fuel consumption.

P2096

Post-catalyst fuel trim system too lean (Bank 1)

Mixture trim measured after the catalytic converter on bank 1 indicates overly lean combustion.

Symptoms: Increased fuel consumption, possible power loss.

P2097

Post-catalyst fuel trim system too rich (Bank 1)

Mixture trim measured after the catalytic converter on bank 1 indicates overly rich combustion.

Symptoms: Increased fuel consumption, fuel smell from the exhaust.

P219A

Cylinder fuel-air mixture imbalance (Bank 1)

The control unit detected significant differences in the fuel-air mixture between individual cylinders on bank 1.

Symptoms: Rough running, vibration, misfiring.

Ignition, fuel injection and misfires

P0011

VANOS — camshaft timing over-advanced (Bank 1)

Intake camshaft timing control (VANOS) on bank 1 is operating out of range — a common fault in BMW engines.

Symptoms: Power loss, rough idle, hesitation when accelerating.

P0012

VANOS — camshaft timing retarded (Bank 1)

Intake camshaft timing control on bank 1 can't keep up with the target setting — usually the VANOS unit or its solenoid.

Symptoms: Power loss, rough running.

P0021

VANOS — camshaft timing over-advanced (Bank 2)

Same as P0011, but affects bank 2 (V engines).

Symptoms: Power loss, rough idle.

P0022

VANOS — camshaft timing retarded (Bank 2)

Same as P0012, but affects bank 2.

Symptoms: Power loss, engine hesitation.

P0087

Fuel rail pressure too low

Fuel pressure in the high-pressure system is lower than required — a common high-pressure pump fault (e.g. N54, N55).

Symptoms: Hesitation, power loss, hard starting, sometimes the engine stalling on its own.

P0201–P0212

Injector circuit — cylinder 1–12

Electrical fault in the injector circuit of the indicated cylinder (the number in the code = the cylinder number).

Symptoms: Rough running, misfiring, power loss.

P0300

Random/multiple cylinder misfire detected

The control unit detects misfiring in more than one cylinder, or can't determine which one.

Symptoms: Engine hesitation, flashing Check Engine light, a noticeable 'kick'.

P0301

Misfire detected — cylinder 1

The control unit detected a misfire specifically in cylinder 1.

Symptoms: Noticeable hesitation, power loss, sometimes a smell of unburnt fuel.

P0302

Misfire detected — cylinder 2

Same as P0301, affects cylinder 2.

Symptoms: Hesitation, rough running.

P0303

Misfire detected — cylinder 3

Same as P0301, affects cylinder 3.

Symptoms: Hesitation, rough running.

P0304

Misfire detected — cylinder 4

Same as P0301, affects cylinder 4.

Symptoms: Hesitation, rough running.

P0305

Misfire detected — cylinder 5

Same as P0301, affects cylinder 5 (R6, V8, V12 engines).

Symptoms: Hesitation, rough running.

P0306

Misfire detected — cylinder 6

Same as P0301, affects cylinder 6.

Symptoms: Hesitation, rough running.

P0307

Misfire detected — cylinder 7

Same as P0301, affects cylinder 7 (V8, V12 engines).

Symptoms: Hesitation, rough running.

P0308

Misfire detected — cylinder 8

Same as P0301, affects cylinder 8.

Symptoms: Hesitation, rough running.

P0325

Knock sensor circuit 1

Fault in the knock sensor circuit — the control unit loses some of its protection against detonation.

Symptoms: Usually no direct symptoms, possible reduced performance in limp mode.

P0330

Knock sensor circuit 2

Same as P0325, affects the second knock sensor (bank 2).

Symptoms: Usually no direct driving symptoms.

P0335

Crankshaft position sensor circuit

Fault in the crankshaft position sensor circuit — critical for ignition and injection timing.

Symptoms: Hard starting, engine stalling, no starter response.

P0340

Camshaft position sensor circuit

Fault in the camshaft position sensor circuit.

Symptoms: Hard starting, rough running.

P0341

Camshaft position sensor — signal out of range

The camshaft sensor signal doesn't match the crankshaft signal — often linked to VANOS or the timing chain.

Symptoms: Power loss, rough running, sometimes a characteristic timing-chain rattle.

P0351–P0358

Ignition coil circuit — cylinder 1–8

Electrical fault in the ignition coil on the indicated cylinder.

Symptoms: Misfiring, hesitation, power loss on that cylinder.

P0316

Misfire detected on startup

The control unit detected a misfire during the first engine cycle after startup.

Symptoms: Rough running right after start-up, which later clears up.

P0327

Knock sensor 1 — signal too low

Voltage from the knock sensor is lower than expected.

Symptoms: Usually no direct driving symptoms.

P0328

Knock sensor 1 — signal too high

Voltage from the knock sensor is higher than expected.

Symptoms: Possible power loss in engine protection mode.

P2122

Accelerator pedal sensor — signal too low (circuit D)

Voltage from one of the accelerator pedal position sensors is lower than expected.

Symptoms: Reduced power, limp mode, uneven throttle response.

P2127

Accelerator pedal sensor — signal too low (circuit E)

Same as P2122, affects the second sensor in the accelerator pedal module.

Symptoms: Reduced power, limp mode.

P2135

Throttle/pedal position sensor signal mismatch

Two signals from the throttle or accelerator pedal sensor don't agree with each other.

Symptoms: Limp mode, significantly reduced engine power.

Emissions: EGR, catalytic converter, DPF, AdBlue, EVAP

P0400

Incorrect EGR flow

General fault in the exhaust gas recirculation (EGR) system — flow deviates from expected.

Symptoms: Rough idle, exhaust smell, increased emissions.

P0401

Insufficient EGR flow

The EGR valve is passing less exhaust gas than the control unit requires — a common cause: a clogged valve or EGR cooler (e.g. N47 diesels).

Symptoms: Hesitation, engine knocking under load, increased fuel consumption.

P0402

Excessive EGR flow

The EGR valve is passing more exhaust gas than it should.

Symptoms: Unstable idle, power loss.

P0403

EGR valve circuit

Electrical fault in the EGR valve control circuit.

Symptoms: Rough running, engine warning light on.

P0420

Catalyst system efficiency below threshold (Bank 1)

The catalytic converter on bank 1 isn't reducing emissions as effectively as required by the standard.

Symptoms: Usually no noticeable driving symptoms — detected via the engine warning light.

P0430

Catalyst system efficiency below threshold (Bank 2)

Same as P0420, affects the catalytic converter on bank 2.

Symptoms: Usually no noticeable driving symptoms.

P0440

EVAP system leak (general)

A leak has been detected in the fuel tank vent system.

Symptoms: Usually no driving symptoms, sometimes a fuel smell.

P0442

Small leak in the EVAP system

A minor EVAP system leak — a very common cause: a leaking or poorly tightened fuel filler cap.

Symptoms: No driving symptoms, just the engine warning light.

P0455

Large leak in the EVAP system

A significant EVAP system leak.

Symptoms: No driving symptoms, sometimes a noticeable fuel smell.

P0461

Fuel level sensor — signal out of range

The fuel level sensor reading changes in a way inconsistent with actual consumption.

Symptoms: Incorrect fuel gauge reading on the dash.

P2002

Diesel particulate filter (DPF) efficiency below threshold

The DPF isn't trapping particulates as effectively as it should — possible damage to the filter element.

Symptoms: Increased emissions, possible power loss in limp mode.

P242F

Excessive soot accumulation in the DPF

The particulate filter is overloaded with soot beyond the allowed limit — regeneration wasn't keeping up or wasn't succeeding.

Symptoms: DPF warning light, power loss, increased fuel consumption.

P2463

Soot accumulation in the DPF — limit exceeded

Similar to P242F — the filter needs regeneration or cleaning/replacement.

Symptoms: DPF warning light, reduced engine power (limp mode).

P204F

Low AdBlue level (NOx reductant)

The AdBlue fluid level in the tank has dropped below the warning threshold.

Symptoms: AdBlue level warning message, risk of a start-up block once it reaches zero.

P2047

NOx reductant injector circuit (AdBlue)

Electrical fault in the injector that doses AdBlue fluid into the exhaust system.

Symptoms: Engine warning light, possible SCR/AdBlue system message.

P0410

Secondary air injection system flow incorrect

Fault in the secondary air system that helps burn off exhaust gases after a cold start.

Symptoms: Usually no driving symptoms, slightly increased emissions on cold start.

P0446

EVAP vent control circuit

Electrical fault in the valve that vents the fuel tank.

Symptoms: Usually no driving symptoms.

P0456

Very small leak in the EVAP system

A very minor EVAP system leak — most often a leaking fuel filler cap.

Symptoms: No driving symptoms, just the engine warning light.

Electronics, control units and additional sensors

P0500

Vehicle speed sensor circuit

Fault in the vehicle speed sensor (VSS) circuit.

Symptoms: Incorrect speed reading, cruise control or ABS problems.

P0501

Vehicle speed sensor — signal out of range

The vehicle speed sensor signal doesn't match other driving parameters.

Symptoms: Incorrect speed reading, cruise control problems.

P0505

Idle control system

The control unit can't maintain the target idle speed.

Symptoms: Idle speed too high or too low, engine stalling.

P0520

Oil pressure sensor circuit

Fault in the engine oil pressure sensor circuit.

Symptoms: Incorrect oil pressure reading, dashboard warning.

P0562

System voltage too low

The control unit detected too-low supply voltage — a common cause: a weak battery or alternator.

Symptoms: Starting problems, flickering warning lights, erratic electronics behavior.

P0563

System voltage too high

The control unit detected too-high supply voltage — a possible alternator fault.

Symptoms: Flickering warning lights, sometimes a burning smell from the wiring.

P0600

Serial communication link (data bus) fault

Communication between the vehicle's control units (CAN bus) has been lost.

Symptoms: Multiple warning lights at once, unpredictable electronics behavior.

P0601

Control module memory checksum error

The engine control unit's internal memory is reporting a data error.

Symptoms: Unpredictable engine behavior, sometimes limp mode.

P0606

Engine control module processor fault

Internal processor error in the engine control unit (DME/DDE).

Symptoms: Limp mode, significant power loss.

P0630

VIN mismatch in engine control unit

The VIN stored in the control unit doesn't match the rest of the vehicle — common after replacing/cloning a control unit without full coding.

Symptoms: Function restrictions, sometimes an inability to start the engine.

P0645

A/C compressor clutch relay circuit

Electrical fault in the relay that engages the A/C compressor.

Symptoms: Air conditioning doesn't cool or doesn't switch on.

P0617

Starter relay circuit — signal too high

Electrical fault in the starter relay control circuit.

Symptoms: Problems starting the engine.

P0620

Alternator control circuit

Fault in the alternator control circuit.

Symptoms: Battery charging problems, battery warning light.

Automatic transmission

P0700

Transmission control system malfunction (reported)

The engine control unit reports that the transmission control unit has detected its own fault — details need to be read from the transmission control unit.

Symptoms: Unusual shifting behavior, sometimes transmission limp mode.

P0705

Transmission range sensor circuit (PRNDL)

Fault in the gear selector lever position sensor circuit.

Symptoms: The car doesn't recognize the selected gear, starting restrictions.

P0715

Input/turbine speed sensor circuit

Fault in the speed sensor at the transmission input.

Symptoms: Jerky, delayed, or incorrect gear shifts.

P0720

Output speed sensor circuit

Fault in the speed sensor at the transmission output.

Symptoms: Incorrect gear shifts, faulty speed reading.

P0730

Incorrect gear ratio (general)

The transmission doesn't reach the expected ratio for the selected gear.

Symptoms: Transmission slipping, hesitation, increased engine RPM without a corresponding increase in speed.

P0731–P0735

Incorrect gear ratio — gear 1–5

Same as P0730, but the fault affects the specific gear indicated in the code.

Symptoms: Slipping or hesitation in a specific gear.

P0740

Torque converter clutch circuit

Electrical or mechanical fault in the torque converter lock-up clutch.

Symptoms: Vibration at steady speed, higher fuel consumption, hesitation.

P0750

Shift solenoid A

Fault in the solenoid responsible for one of the gear shifts.

Symptoms: A specific gear shift missing or incorrect.

P0755

Shift solenoid B

Same as P0750, affects another solenoid.

Symptoms: A specific gear shift missing or incorrect.

P0760

Shift solenoid C

Same as P0750, affects another solenoid.

Symptoms: A specific gear shift missing or incorrect.

P0765

Shift solenoid D

Same as P0750, affects another solenoid.

Symptoms: A specific gear shift missing or incorrect.

P0741

Torque converter clutch — stuck off

The torque converter lock-up clutch doesn't engage despite the control unit's signal.

Symptoms: Higher fuel consumption, vibration at steady speed.

P0743

Torque converter clutch circuit electrical

Electrical fault in the torque converter clutch control circuit.

Symptoms: Hesitation, abnormal behavior at steady speed.

P0613

Transmission control module (TCM) processor fault

Internal processor error in the automatic transmission control unit.

Symptoms: Transmission limp mode, limited number of available gears.

Communication between control units (U codes)

U0100

Lost communication with ECM/engine control module

Another control unit in the vehicle reports a loss of communication with the engine control unit on the data bus.

Symptoms: Multiple warning lights at once, unusual electronics behavior, sometimes no start.

U0101

Lost communication with TCM (transmission control module)

Loss of communication with the automatic transmission control unit.

Symptoms: Transmission in limp mode or no response to gear changes.

U0121

Lost communication with ABS/DSC control module

Loss of communication with the ABS/stability control unit.

Symptoms: ABS and DSC warning lights, sometimes a firmer brake pedal.

U0140

Lost communication with body control module (BCM)

Loss of communication with the module responsible for comfort functions and body electrics.

Symptoms: Problems with central locking, windows, lighting.

U0155

Lost communication with instrument cluster

Loss of communication with the dashboard instrument cluster.

Symptoms: Incorrect or blank readings on the dash.

U0164

Lost communication with HVAC control module

Loss of communication with the automatic climate control unit.

Symptoms: Climate control doesn't respond to settings, no temperature display.

U0184

Lost communication with radio/infotainment module

Loss of communication with the infotainment or radio module.

Symptoms: Radio, navigation or infotainment screen not working.

Chassis codes — ABS, DSC and brakes (C codes)

C0035

Wheel speed sensor circuit — front left

Fault in the front left wheel speed sensor circuit.

Symptoms: ABS/DSC warning light, possible deactivation of stability control.

C0040

Wheel speed sensor circuit — front right

Same as C0035, affects the front right wheel.

Symptoms: ABS/DSC warning light.

C0045

Wheel speed sensor circuit — rear left

Same as C0035, affects the rear left wheel.

Symptoms: ABS/DSC warning light.

C0050

Wheel speed sensor circuit — rear right

Same as C0035, affects the rear right wheel.

Symptoms: ABS/DSC warning light.

C0110

ABS/DSC pump motor circuit

Electrical fault in the ABS/DSC modulator's hydraulic pump motor.

Symptoms: ABS/DSC warning light, no assistance in emergency braking situations.

C0161

Parking brake switch circuit

Fault in the parking brake switch/sensor circuit (electric or manual).

Symptoms: Incorrect parking brake status shown on the dashboard.

C0200

Wheel speed sensor circuit — general fault

General fault in one of the wheel speed sensor circuits, without indicating a specific wheel.

Symptoms: ABS/DSC warning light.

// Common BMW failure patterns

Not everything comes down to one simple fault code.

Some of the most common BMW faults don't boil down to a single code number — they're whole, well-known failure patterns typical of specific engines.

Timing chain (N47, N53, N43, N20)

A stretched or jumped timing chain — a characteristic rattle on cold start, sometimes paired with camshaft position sensor codes (e.g. P0341). See more about the N47/N57 timing chain.

VANOS — camshaft timing control

Power loss and rough idle, often with codes P0011, P0012, P0021 or P0022 — the culprit is often the VANOS solenoid or the adjustment mechanism itself.

High-pressure fuel pump (N54, N55)

Hesitation, power loss and hard starting — the typical picture when fuel rail pressure is too low (code P0087) in direct-injection engines.

EGR cooler (diesel engines, e.g. N47)

A leaking EGR cooler is a common cause of codes P0401/P0402 and engine knocking under load in BMW diesels.

Recognize any of these symptoms in your car? Also check our classic BMW engine diagnostics or write to us with a description — we'll help figure out what's going on before your visit.

// Frequently asked questions

Questions about fault codes and diagnostics.

A fault code, e.g. P0301, is a standard OBD2 number that points to the area of the fault — a specific cylinder, sensor or system. The code alone doesn't always say outright which part is damaged — sometimes that has to be confirmed with on-site measurements.

A simple OBD2 reader will show you just the code number, but full diagnostics on professional equipment also lets us check live parameters and actually confirm the cause of the fault, not just the code itself.

No — clearing the code only turns off the engine light. If the cause of the fault hasn't been fixed, the code will come back, usually after a handful of drives.

Not always — some codes, like a minor EVAP system leak, don't noticeably affect driving, while others, like a misfire or too-low fuel pressure, can lead to more serious damage if you ignore them.

Send us the code number and we'll check it during diagnostics — we handle the full range of BMW codes, not just the ones described on this page.

Send us the code number and your car model, and we'll give you exact terms before you book a visit.

Got a fault code and don't know what's next?

Send us the code number and your BMW model — we'll tell you what's actually worth checking and what the repair looks like.

Get in touch

See also

New: SC Diag — BMW engine diagnostics on your phone and laptopAn Android app and a Windows program: reads BMW and MINI engine control units (97 ECUs, petrol and diesel). Silesia Codemasters prepares the log analysis and report.See the app →
f